Release Notification - Operations Manager 21.Q1.0 is now Generally Available – Opengear Help Desk

Operations Manager 21.Q1.0 is now generally available for OM2200 and OM1200 models.

21.Q1.0 (March 2021)
New features in this release:
 - Support for OM120xx SKUs with dual AC power supply
 - Support for OM2224-24E SKUs
 - Improved list access in ogcli
 - Remove Non-Inclusive Language References from WebUI
 - SNMP Traps for PSU and system temperature
 - Automatic failover support - AT&T and Verizon
 - Password Complexity Enforcement
 - New bridge inherits MAC address of the primary interface

Known issues in 21.Q1.0:
 - Serial ports insensitive to pinout change when in localConsole mode
  - The workaround is to change the mode to consoleServer, change the pinout and then change the mode back to localConsole.
 - The ogcli command "get ssh/authorized_key" as listed by "get ssh/authorized_keys" does not work
  - There is no workaround, "get ssh/authorized_keys" can be used to retrieve the full list
 - Logging in to USB serial port in localConsole mode is unreliable
  - There is no workaround, please use another serial port in localConsole mode
 - Upgrade can fail silently due to old log files present on the system
  - If this occurs, remove the following directories and try again:
    /mnt/nvram/0/log
    /mnt/nvram/1/log
 - Issues accessing some Cisco devices via USB serial port
  - There is no workaround, please use another serial port.
 - SNMP Networking Alerts do not work for Cell Interface Link State
  - There is no workaround
 - SNMP temperature alert trap is not triggered if ranges are changed until next time is out of range
  - There is no work around

Defects fixed since 20.Q4.0:
 - ModemManager can probe the local console
 - Description field on create bond/bridge is not cleared after submit
 - 10G IPv6 crashes
 - "ogcli update" is broken for all non-cellular interfaces
 - Deleting an aggregate underneath a VLAN gives a confusing error message
 - Cell Modems may come out of Auto-SIM mode
 - "Internal Error." is not a useful REST API error message
 - Changing sim during failover causes device to come out of failover mode
 - Allow uploading of firmware images over 400M
 - "Port Number for Direct SSH Links" not working
 - Console user can see the edit button on Access > Serial Ports page
 - Aggregate creation errors not shown in web UI when f2c/failover is updated
 - SNMP agent sometimes reports ports out of order
 - Port Discovery requires multiple runs to complete
 - Inform user of failure to add IP Alias to serial port configured as a local console
 - Auto-Response Salt Master and Minion may not always sync keys
 - REST failure messages not correctly reported in WebUI on Network Interfaces page
 - Firewall Interzone Policy dropdowns show duplicate values when adding multiple entries
   - Redesigned UI to improve user experience
 - odhcp6c script removes all IPv6 addresses and routes every time an RA event occurs
 - search parameters in '/ports' isn't working
 - Cannot use special characters in cell APN or username
 - Portmanager does not re-open USB device after it is connected in some cases
 - Access via Lighthouse proxy not working from behind NAT
 - Configuration allowed multiple SNMP managers with the same destination and different message-types and protocol.
   - This resulted in multiple messages being received via SNMP.
   - Now it is invalid to have multiple SNMP managers with the same destination; each entry must have a unique combination of host, port and protocol.
   - Note: During upgrade to 21.Q1.0, if multiple entries with the same host, port and protocol are found, only the first entry will be kept.
 - Mask client passwords in Support Report output
 - Modem not present during initial boot, fails on subsequent boots
 - Session tokens visible in URLs
  - Session APIs are updated to not contain any session tokens
  - Compatibility note for CURL users: POSTing to sessions and following the redirect (-L) without allowing cookies (-c /dev/null) will result in an error

Firmware is available here:

https://ftp.opengear.com/download/operations_manager/current/

Full release notes including other changes are here:

https://ftp.opengear.com/download/operations_manager/Release_notes.txt